Qingdao Pacific Container Co.,Ltd
Contact US
Address: No.373 Maoshan Road, Qingdao Economic & Technical Development Zone, China
TEL: +86-532-86916160
FAX : +86-532-86916182
Singamas Qingdao Factory Directly Produce and Sell 20ft Three Side Door Open Container

Singamas Qingdao Factory Directly Produce and Sell 20ft Three Side Door Open Container

The rear frame consists of one door header, one door sill, four corner castings and two rear corner posts.

    1.The Rear Frame

    The rear frame consists of one door header, one door sill, four corner castings and two rear corner posts.

    1.1 Rear Corner Post

    Each corner post is constructed from an inner part of channel shaped hot-rolled section steel and an outer part of steel pressing, welded together to form a hollow section to ensure the door opening and suitable strength against the stacking and racking force. Four (4) sets of hinge pin lugs are welded to each outer part of the corner post.

    1.2 Door Header

    The door header is constructed from a lower part of a "U" shaped steel pressing with internal stiffener ribs at the location of the cam keeper’s backside and an upper part of steel pressing rear header plate, they are welded together to form a box section to provide a high rigidity.

    1.3 Door Sill

    The door sill is built of a special channel section steel pressing with internal ribs as stiffeners at the backside of each cam keeper. The upper face of the sill has a slope for better drainage and the highest part is on the same level to the upper face of the wooden floor. Two channel section steel recesses are provided adjacent to the bottom casting to prevent damage due to any twistlock misalignment.

    2.Side Wall Assembly

    The side walls will be continuously welded to each other and to the side rails and corner posts. Welding penetration side panels to rails should be min.75%.

    2.1 Top Side Rails

    Each top side rail is used a square steel pipe.          

    2.2Side Walls

    Each side wall will be composed of a number of sheets for the intermediate (inner) parts and outer panels at each end of side wall, fully vertically corrugated into trapezium section, butt welded together to form one panel by automatic welding. 

    3.Roof

    The roof will be constructed by several die-stamp corrugated steel sheets with a certain upwards camber at the center of each trough and corrugation, these sheets are butt jointed together to form one panel by automatic welding.


    TYPE

    4QG2

    Extermal

    Side Door Opening

    Length

    Width

    Height

    Width

    Heigh

    12,192 mm

    2,502 mm

    2,060 mm

    11,584mm

    1,600mm

    40'

    8'-2 1/2”

    6’- 9 3/32”

    38’-1/16”

    5’-2 31/32"

    Internal

    Weights

    Length

    Width

    Height

    Max Gross Weight

    Tare Weight

    Max Payload

    12,094 mm

    2,422 mm

    1,657 mm

    28,220   Kg

    5,720 Kg

    22,500 Kg

    39’- 8 1/8”

    7’-11 11/32”

    5’- 5 7/32”

    62,214  Lbs

    12,610 Lbs

    49,604 Lbs

    Cubic Capacity

    Allowable Stacking Weigh

    48.5 cu.m

    1,708 cu.ft

    60,960 Kg

    134,394 Lbs


    Special Feature

    1.Side doors on both sides makes cargo loading and unloading easy.


    PACIFIC CONTAINER, one of the largest manufacturers and suppliers in China, is equipped with the most advanced equipment and technology. And catering to your special requirement, our factory also offer you the customized service. Welcome to buy the singamas qingdao factory directly produce and sell 20ft three side door open container with us.

Related Products
Inquiry